Want to Buy: 98-00 steel ext cab 4x4 rear driveshaft
Looking for a steel not aluminum rear single piece rear shaft to swap into my 97 extended cab 4x4. Thanks, Dan
View Article2001 4.0 into 99 4.0
I have a 99 ranger xlt 4.0 auto that I just lost compression in cillinder a 1 and 4 just picked up an 01 xlt that's 4.0 standard what am i up against to try and swap motors
View Article2000 3.0L V6 4x4 engine swap to 2.5 4cyl?
Hey all, quick question I have a 97 ranger manual trans with a brand new jasper 2.5L engine with 5,000 miles on it. I have the opportunity to purchase a 2000 xlt supercab automatic with a 3.0 v6 4x4...
View ArticleFor Sale: 99 xlt 3.0 standard parting out
I have a 99 3.0 L flex fuel standard I'm parting out drive train is good bad rear frame and steering rack most everything else is good located in central VT
View ArticleWho makes a redesigned Slave Cylinder?
Im about to replace the clutch in my ranger. Now my dilemma is the slave cylinder in the truck appears to be working fine and not leaking. I don't really want to change it if I don't have to. *If its...
View ArticleDrivers door random locking
2011 Ford Ranger Sport 4x4 manual transmission. Drivers door randomly locks. Sometimes by hitting door panel, other times just by opening door, some times while driving, sometimes just sitting there...
View ArticleClik here to view.
Mustang GT hood scoop to Ranger?
Well I really want to put a hood scoop on my truck. Going to flat black the hood and scoop. I came across this picture, and did some research to find out its from a GT. So the link below is what I may...
View ArticleRunning boards
My son used to own a 1995 Ford Explorer 2 door. He removed the running boards from it, and they got stashed away up in the attic. I have a 2000 Ford Ranger 4 door 4x4, and was wondering if those...
View Article33 inch tires on factory suspension
Hi everybody, I have a 99 ranger sport supercab 4x4, and was wondering if i could clear 33s without rubbing too bad. Its got 3" blocks in the rear from the factory and i cranked the torsion bars up...
View ArticleIntake manifold
Hello everyone, im new to this so i hope this works! I have a 2003 ford Ranger with a 2.3 engine. I wanted to know if anyone can tell me how to replace the intake manifold cuz the mechanic thinks thats...
View ArticleSticky*?? - Engine Replacement Guides, Tips & Tricks, Exclusivity to Engine...
Moderator - please post this where it shall fit best. This is general knowledge but most people dont think about the benefits from it. Over the years ive worked for multiple dealerships from sketchy...
View ArticleHayden tranny cooler and Derale fittings
Not sure were to post my first post. So, move it if necessary. And, if the info is repetitious, then "so sorry." I embarked on installing a transmission cooler on my 2011 Ranger 2x2 2.3l. Being "old...
View Article40 hp increas4
I am looking to add about 40 hp to my 2011 2.3l Ranger with auto tranny. I suspect it might be doable, but I don't know if it can be done without adding aftermarket cams, intake manifold, modifying...
View ArticleClik here to view.
Lift Suggestions
I've been wanting to lift my truck (05 Edge) pretty much since I got it and after years of looking at my different options I believe I have come to somewhat of a decision. My main goal has been to fit...
View ArticleWant to Buy: 1354 Manual shift linkage bolts
Just bought a 1354 manual shift t-case but the yard didn't have the bolts that connect the linkage to the trans tail shaft. Anyone have extra bolts laying around for this that you would sell? Thanks, Dan
View ArticleAnother new from KC
Hi I have a 2000 Ranger XLT 4x4. It has almost 300k and I have had to replace and repair many things on it. It is still a solid truck that I drive every day. I am here because many times I have...
View ArticleQuestion about manual transmission
Quick question. There are three bolt plugs in my manual transmission. Two large ones on the driver's side are fill and drain. There is a smaller one high up on the passenger side. Does anyone know what...
View Articlenew type of relay/fuse panel and heavy duty relay
this is a new type of relay block with built in ( replaceable ) fuses 1 main power feed in ---- 2 -relay/fused power leads out , with trigger connectors Dual 70 Amp Relay Board they finally came out...
View Article4.0 sohc parts compatibility?
Hi , I'm new to the site (not to engines). I am going to buy a 2011 ranger that caught my eye and created new questions. It is listed as a 4.0 sct edition cobra. My first question is , why cant I find...
View Articlemystery motor water pump fiasco....
I'm REALLY new here. I bought an 81 ranger in Dec. Its been a great work truck but I've got a mystery motor ( I mentioned that in my introduction on the getting to know you thread) my buddy Bill down...
View Article