signal lights problem
I have a 95 ranger the signal lights are acting funny When the head lights are on and I turnthe signal on and step on the brake the back goes and the front flashes real fast when the headlights are off...
View Article16" Ranger steelies....?
Thinking about a set of winter wheels for my 03......... Don't recall seeing any..... Looking for something to mount the stock size tires.....on a 16 x 7 with the same offsett as the alloy 16 x 7's......
View Articleclunking noise, thanks
My slip yoke was bone dry, greased it up real good. I cannot see how that could make that much noise but all fixed thanks to you guys,again thank you
View ArticleSwap from 94 Ranger to 94 B4000
Hi all, I have a 94 B4000, my daily driver, that has been running on 5 cylinders for about a year now. Top end of the motor ticking really bad, and there is a knock in the lower end. Still gets me from...
View Article2005 3.0 mystery vacuum port
I have a 3.0 Edge automatic, I bought it not running. There is a black plastic tube sticking out located just past the throttle valve. It is open to manifold vacuum. I have it plugged and the truck...
View ArticleCoil issues
I have a 93 2.3 ranger that is only firing on half of both coils. I have tested both coils and they show the proper resistance. The ICM was just pulled and has tested ok as well. The best i can tell 2...
View ArticleStrange power port problem
I plug into my power port with a splitter to power a refrigerator and gps when I am travelling. This has worked very well for many years. On my last off-road trip I started having problems and ended up...
View ArticleBattery not being charged..
Hello Ranger Forums, I have a 1993 Ford Ranger XLT, with 458,000k miles ( yep! ). I've never tried to get help with my ranger, because it's just never needed it... until now. So this is my first post...
View Articlecomes out of gear when slowing down?
Hi this is my first post , lets see what happens...I have a 97 ranger 4x4 3.0 manual, trans shifts smooth but the problem is that when i take tension of the trans by slowing down it comes out of gear...
View ArticleAZ Newbie
Howdy everyone! I'm Jon in Arizona. :sombrero: Just got my transfer case motor working again, by taking apart and cleaning the blue disc. Now it has me thinking about the SAS I've been wanting to do....
View Articlefuel gauge problem
So I have a 1990 ford ranger 2.9l, just replaced fuel pump due to float filling with gas and my fuel gauge not working, but now it reads about a 1/4 off, showing I have more gas in it. Anyone have any...
View ArticleDoor cables 1/2 door
I have a 2001 ranger xlt with the extended rear doors. I replaced the latch cable ends but the door still will not lock at the top or release at the bottom. If I unhook the cables from the handle it...
View ArticleHigh idle when shifting
Has anyone figured out the high idle when shifting Its driving me crasy.
View Article1st/2nd Syncros going out?
Hey everyone, Well my 5-speed is deciding to really crap out on me lately. I had been wanting to swap out the Transmission for a T5 or similar so it feels more like a car and also since it has 292k on...
View ArticleLOST!!!!!
Working on moms 2000 3.0. Felt rough. Pulled codes and came up with PO153 (Bank 2 Sensor 1) & PO430 (catalyst system efficiency below threshold (bank 2)). So I did the O2 sensor. No response. Took...
View ArticleClik here to view.
New CO member, now with pics!
Hi all, this is my second intro, but I did not know how to post pics the first time, so hopefully this is a better. 1994 Ford Ranger 2.3L XLT w/90K miles. Body work complete, now awaiting paint. Was my...
View Articlepinging on 87 octane
Is possible that egr is bad, truck is throwing no codes, need help with this, under partpartil throttle from dead stop,but won't do it in of going45 and give it gas without kicking down a gear, any...
View ArticleHow do you replace truck bed on 02 Ranger Edge stepside bed?
The inside bed on my 02 Ford ranger Edge stepside is rusting out and starting to come lose on the one side, how do you take the bed off to put a replacement one on? is it hard to do? and is it worth it...
View ArticleEGR Code
Engine code says egr valve insufficient flow. Replaced the EGR valve, cleaned the tube from exhaust to valve. Cleared the code. Ran for a day and engine code came back. Any suggestions?
View Article